Spot Sensors and Cable Type Sensors
Indoor Diesel Fuel Detector
- Use on concrete floor or in drip pan
- Instant response to diesel fuel, jet fuel, gasoline
- Resettable
- Tool free, replaceable sensor element for quick restoration of service
Rapid Detection for non-volatile oils
- Detects: Mineral Oil (transformer oil) , Hydraulic Oil, Lube Oil and others
- Ignores water
- Tool free, replaceable sensor element for quick service restoration
Water and Coolant Sensor for Indoor Applications
- Use to detect leaking water of water/glycol coolant
- Compliment to TRM-DFS fuel and IOS oil sensors
- Instant reset when lifted from spill
Water and Coolant Sensor for Indoor Applications
- Use to detect leaking water of water/glycol coolant
- Compliment to TRM-DFS fuel and IOS oil sensors
- Instant reset when lifted from spill
“Micro” water sensor cable for water/glycol cooled electronics
- Diameter less than 2 mm
- Flexible to conform to small gauge water tubing
- Designed for direct integration to mother-boards and OEM electronics
Water detection and locating cable for steam conduit and other high temperature environments.
Outdoor Sump Sensors / Double Wall Tank and Pipe Sensors / Acid, Caustic and Brine Sensors
Fuel / Crude Oil Sensor for Wet or Dry Sumps and Containment Area
- Use outdoor containments or vaults
- Responds to fuels, crude oil, gas condensates
- 3 sizes; 9″ (225 mm), 35″ (890 mm) and 59″ (1500 mm)
- Ignores rain, snow melt, condensation
- Replaceable Core
Combination Fuel/Water for Double Wall Tanks and Pipe
- Use to monitor the interstitial space of double wall tanks and low points in double wall pipe systems
- Detects presence of diesel, gasoline, or jet fuel
- Detects ground water intrusion
Hazardous Fluid Sensors
- Ignore Rain Water and Snow Melt
- Detect highly conductive fluids such as brine, acids, caustic process waste
- Model for sumps, vaults, and buried flange monitoring
Monitoring Devices
cULus approved monitoring device for all TRM sensors
- Monitor up to 20 TRM-DFS-3 indoor diesel sensors; 2 TRM-IOS, 10 TRM-WLS or 2 TRM-UST or 2 TRM-CC
- Relay outputs to connect to BMS, alarm panels or similar site wide monitoring
- Direct control of optional alarm annunciator for facility office or security desk.
cUlus approved monitoring device for all TRM sensors
- Status screen display for instant alarm diagnosis
- Same monitoring capabilities as TRM-Easy5-Relay-U
- Relay outputs to connect to BMS, alarm panels or similar site wide monitoring
- Can directly control alarm annunciator for facility office or security desk.
UL508A Certified Panel with choice of TRM-Easy5-Relay-U or TRM-Relay-SDR controller
- Ready to bolt on the wall
- Includes line voltage (100 Vac to 240 Vac) power supply
- All internal wiring
- Terminal blocks for sensors, relays, remote alarm, line voltage
Remote Alarm or Free Standing Controller for TRM-ALOS or TRM-DFS-3 systems
Mount in security station of facility office or along side Easy 5 panel
Loud buzzer, red LED lighted pushbutton. Push button to silence buzzer but red LED stays on until leak is cleared.
As remote alarm, power and control come from monitoring panel.
As free standing controller power comes from plug-in adapter or from 12 /24 Vdc supply
2 x SPDT (Form-C) alarm output relays
Specialty Adapters
TRM Opto-to-Relay Adapter is designed to interface GEMS sink type optical level sensors to devices that accept a normally open dry contact as input.
- Use to interface three wire GEMS sink type optical level sensor to TraceTek TT-SIM modules
- Requires either 12 Vdc or 24 Vdc supply voltage
- Single, normally alone dry contact as output signal to monitor device
Monitors TRM-DFS-3; TRM-IOS; TRM-WLS and TRM-CC probes
- Requires 24 Vdc supply
- Outputs distinct current levels in the 4-20 mA range that signal probe status
- Used to interface TRM’s resistance based sensors to monitoring equipment that required 4-20 mA input
Allows TRM-DFS-3; TRM-IOS or TRM-CC probes to be monitored by TraceTek’s TT-SIM network
- Operates on micro-amp current dervived from TT-SIM normal monitoring opeation
- Converts TRM’s “normally-low” resistance state to the “normally-high” resistance state required for TT-SIM operation
- Allows TRM sensors to directly replace or expand aging TT-FFS system to exploit legacy TTDM/TS-12/TT-SIM networks
Specialty adapter that allows 4-wire sensor cables to be monitored by TRM-Easy5-SDR
- Mounts directly onto TRM-SDR terminal block with terminals for supply voltage and leader cable
- Requires 12 to 24 Vdc voltage supply
- Monitors TRM-Waterwire-HT or any TraceTek/RLE/TTK 4-wire sensor cable
- Provides mappable leak location on TRM-Easy5-SDR status screen when a leak is detected.